Page 1 of 1
Unable to change configuration variables
Posted: Fri Sep 18, 2020 7:52 pm
by fernando
Dear support, I couldn't go any further than 5.4 Configuration.
OpenEMMInstaller dos not allow me to change system.url and birt.drilldownurl, as you can see below, they even exists in the menu:
Code: Select all
================================
= OpenEMM Installer v20.04.003 =
================================
Host: mm3.v2v.net
License: OpenEMM (ID: 0)
Runtime Version: 20.04.000.043
Manual Version: 20.04.011
OpenEMM Version: 20.04.000.188
System-Url: Unknown
OpenEMMBackend Version: 20.04.000.190
Current menu: Change configuration of installation in DB
OpenEMM configuration in DB
clean.mastercompany = true
mailloop.actionbased_autoresponder_ui = enabled
system.<hostname>[to be defined].IsActive = 1
system.licence = 0
system.mm3.v2v.net.IsActive = 1
system.RdirLandingpage = http://www.openemm.org
system.support_emergency_url = http://www.openemm.org/systemstoerung
Please choose entry name to change (Blank => Back):
>
I've even try these parameters, but the script returns "Invalid entry key name: system.url"
Am I missing something?
Best regards!
Re: Unable to change configuration variables
Posted: Fri Sep 18, 2020 8:39 pm
by maschoff
Your list of properties does not show parameter system.url at all, or is your post incomplete?
Which value does file emm.properties hold for property system.url?
Re: Unable to change configuration variables
Posted: Fri Sep 18, 2020 9:38 pm
by fernando
Hello maschoff, the list does not show system.url or birt.drilldownurl. My post is not incompleted.
I've tried rebuild OpenEMM database, but it turns out with the same parameters as showed here.
Re: Unable to change configuration variables
Posted: Sat Sep 19, 2020 6:58 am
by maschoff
Please answer my 2nd question too.
Re: Unable to change configuration variables
Posted: Tue Sep 22, 2020 4:04 pm
by fernando
Hello maschoff, sorry for the delay.
The value for system.url and birt.drilldownurl was something like [to-be-defined] on emm.properties
I've changed the values to my domain, but it still doesn't work.
Re: Unable to change configuration variables
Posted: Tue Sep 22, 2020 4:22 pm
by maschoff
Did you do the change before updating to 20.04 after it?
Re: Unable to change configuration variables
Posted: Wed Sep 23, 2020 1:30 pm
by fernando
This is a new installation. I've changed after the installation.
best regards!
Re: Unable to change configuration variables
Posted: Wed Sep 23, 2020 1:55 pm
by fernando
Below is a selection form config_tbl table:
Code: Select all
mysql> select * from config_tbl;
+----------+------------------------------------+---------------------------------------+----------+
| class | name | value | hostname |
+----------+------------------------------------+---------------------------------------+----------+
| system | licence | 0 | NULL |
| system | support_emergency_url | http://www.openemm.org/systemstoerung | NULL |
| system | RdirLandingpage | http://www.openemm.org | NULL |
| system | <hostname>[to be defined].IsActive | 1 | NULL |
| mailloop | actionbased_autoresponder_ui | enabled | NULL |
| clean | mastercompany | true | NULL |
| system | mm3.v2v.net.IsActive | 1 | NULL |
| system | wkhtmltopdf | /usr/local/bin/wkhtmltopdf | NULL |
| system | wkhtmltoimage | /usr/local/bin/wkhtmltoimage | NULL |
+----------+------------------------------------+---------------------------------------+----------+
9 rows in set (0.00 sec)
and
Re: Unable to change configuration variables
Posted: Fri Sep 25, 2020 10:00 am
by aso
In LTS 20.04 all relevant configuration properties are migrated from emm.properties in db config_tbl for later use in LTS 20.10.
This happens on EMM startup. SO if the values are included in emm.peroperties an you (re-)start up your EMM the values should pop up in config_tbl.
Re: Unable to change configuration variables
Posted: Tue Sep 29, 2020 11:18 pm
by fernando
Dear support,
today I've updated the installer to v20.10.018. My installation is working now.
Thank you for your help an patience.
Best gegards!
Fernando
Re: Unable to change configuration variables
Posted: Fri Nov 26, 2021 8:12 pm
by maschoff
I can not see the message.